This product is not available in region
overview
Range consist of 8 customizable models.
According to the room temperature the range is divided as follows:
- GSE H4 for higher temperatures (≥ +2 °C) with 4 mm fin spacing;
- GSE L7 for lower temperatures (≥ –25 °C) with 7 mm fin spacing, electric defrost version (ED) is recommended.
On request the models can be equipped with non-standard coils, defrosting and fan motors.
Range consist of 8 customizable models.
According to the room temperature the range is divided as follows:
- GSE H4 for higher temperatures (≥ +2 °C) with 4 mm fin spacing;
- GSE L7 for lower temperatures (≥ –25 °C) with 7 mm fin spacing, electric defrost version (ED) is recommended.
On request the models can be equipped with non-standard coils, defrosting and fan motors.
applications
- Small cold rooms
- Walk-in cabinets
- Low ceiling commercial refrigeration cold rooms
- Small cold rooms
- Walk-in cabinets
- Low ceiling commercial refrigeration cold rooms
capacity range
From 1,85 to 7,6 kW
From 1,85 to 7,6 kW
Technical Information
Coil features
- The entire range is equipped with highly efficient coils made from aluminum fins and inner grooved tube. Thanks to a new geometry there is a substantial reduction of the inner volume resulting in a decreased refrigerant use.
- The updated coil design responds to the recent guidelines governing the reduction of HFC gases with high greenhouse effect.
- The entire range is equipped with highly efficient coils made from aluminum fins and inner grooved tube. Thanks to a new geometry there is a substantial reduction of the inner volume resulting in a decreased refrigerant use.
- The updated coil design responds to the recent guidelines governing the reduction of HFC gases with high greenhouse effect.
Casing
- Made of a magnesium aluminum alloy, with a smooth finish covered by a plastic protection film.
Fan motors
The standard AC fan motors employed have the following features:
Ø 315 mm
- fan motor module: from 1 to 4
- external rotor
- single phase 230V/1/50-60 Hz
- built-in electric capacitor
- epoxy coated steel fan guard
The optional high efficiency EC fan motors have the following features:
Ø 300 mm
- fan motor module: from 1 to 4
- external rotor
- single phase 230V/1/50-60 Hz
- epoxy coated steel fan guard
The standard AC fan motors employed have the following features:
Ø 315 mm
- fan motor module: from 1 to 4
- external rotor
- single phase 230V/1/50-60 Hz
- built-in electric capacitor
- epoxy coated steel fan guard
The optional high efficiency EC fan motors have the following features:
Ø 300 mm
- fan motor module: from 1 to 4
- external rotor
- single phase 230V/1/50-60 Hz
- epoxy coated steel fan guard
Defrost
Wiring
- The electric parts and casework are connected to an earth terminal.
- The wiring of the fan motors and heaters is carried out in separate IP 54 protection grade junction boxes.
Certifications
- CE
- PED
- TÜV SÜD (Please see cerfified model list on the catalogue)
Published data
- EN 328 reference standard.
- Nominal capacity assessed in practical operating ambient i.e. in wet conditions.
- R448A refrigerant (media glide).
- Air inlet temperature 0 °C.
- Evaporating temperature –8 °C.
- TD 8 K.
- EN 328 reference standard.
- Nominal capacity assessed in practical operating ambient i.e. in wet conditions.
- R448A refrigerant (media glide).
- Air inlet temperature 0 °C.
- Evaporating temperature –8 °C.
- TD 8 K.
Downloads
Scelte Selection Software
SCELTE is a web based application to select all ECO™ branded coolers and to configure bespoke models.
The selection engine is faster than ever and will allow you to select the unit that suit your requirements, also thanks to a comprehensive database with all new generation refrigerants available on the market.
