This product is not available in region
overview
Our AP range is specifically designed for installations that use latest generation of A2L low GWP refrigerants, especially those used for wall application in reach-in cabinets, display cases and small walk-in cold rooms.
The range consists of 5 customizable models.
For room temperatures down to –5 °C the special electric defrost version is advisable, whereas for lower temperatures (≥ –12 °C) an additional electric heater in the drip tray is recommended.
On request the models can be equipped with non-standard: coils, defrosting and fan motors.
Our AP range is specifically designed for installations that use latest generation of A2L low GWP refrigerants, especially those used for wall application in reach-in cabinets, display cases and small walk-in cold rooms.
The range consists of 5 customizable models.
For room temperatures down to –5 °C the special electric defrost version is advisable, whereas for lower temperatures (≥ –12 °C) an additional electric heater in the drip tray is recommended.
On request the models can be equipped with non-standard: coils, defrosting and fan motors.
applications
- Reach-in cabinets
- Display cases
- Small cold rooms
- Reach-in cabinets
- Display cases
- Small cold rooms
capacity range
from 0,45 to 2,56 kW
Accepted A2L refrigerants:
- R455A
- R454C
- R1234yf
- R1234ze
from 0,45 to 2,56 kW
Accepted A2L refrigerants:
- R455A
- R454C
- R1234yf
- R1234ze
Technical Information
Coil features
- The entire range is equipped with high efficiency coils suitable for A2L refrigerants made from special profile aluminium fins and inner grooved copper tube.
- Dual fin spacing 3,5/7 mm.
- The updated coil design responds to the recent guidelines governing the reduction of HFC gases with high greenhouse effect.
- The entire range is equipped with high efficiency coils suitable for A2L refrigerants made from special profile aluminium fins and inner grooved copper tube.
- Dual fin spacing 3,5/7 mm.
- The updated coil design responds to the recent guidelines governing the reduction of HFC gases with high greenhouse effect.
Casing
- Casing Features Made of a magnesium aluminum alloy, with a smooth finish covered by a plastic protection film.
Fan motors
The standard AC fan motors employed have the following features:
Ø 230 mm
- fan motor module: from 1 to 3
- single-phase 230V/1/50-60 Hz
- fibreglass charged polyamide fan guard
The optional high efficiency EC fan motors have the following features:
Ø 230 mm
- fan motor module: from 1 to 3
- single-phase 230V/1/50-60 Hz
- fibreglass charged polyamide fan guard
The standard AC fan motors employed have the following features:
Ø 230 mm
- fan motor module: from 1 to 3
- single-phase 230V/1/50-60 Hz
- fibreglass charged polyamide fan guard
The optional high efficiency EC fan motors have the following features:
Ø 230 mm
- fan motor module: from 1 to 3
- single-phase 230V/1/50-60 Hz
- fibreglass charged polyamide fan guard
Defrost
Wiring
- The fan motors and the electric heaters of the EP/B models are prewired in IP 54 junction boxes.
Certifications
- CE
- PED
Published data
- EN 328 reference standard.
- Nominal capacity assessed in practical operating ambient i.e. in wet conditions.
- R1234yf and R454C refrigerants.
- air inlet temperature 0 °C.
- evaporating temperature –8 °C.
- TD 8 K.
- EN 328 reference standard.
- Nominal capacity assessed in practical operating ambient i.e. in wet conditions.
- R1234yf and R454C refrigerants.
- air inlet temperature 0 °C.
- evaporating temperature –8 °C.
- TD 8 K.
Downloads
Scelte Selection Software
SCELTE is a web based application to select all ECO™ branded coolers and to configure bespoke models.
The selection engine is faster than ever and will allow you to select the unit that suit your requirements, also thanks to a comprehensive database with all new generation refrigerants available on the market.
